The lot-code line is blank. The parts are already cut. You set the deburring wheel to idle and lean one hip against the workbench, the crinkle of this traveler under your palm a quiet reminder you may not move to the next operation without filling that line first. The 6061 bar stock you ran this morning sits stacked in a wire bin to your left, each part’s edge still sharp enough to catch a work glove if you aren’t careful.
This Traveler’s Lot Code Matching Rules
The lot code you write here ties every part in this 42-unit run to its material origin, machine parameters, and shift log, eliminating guesswork if a random part fails tolerance three operations from now. You follow four fixed steps to build the code, no deviations, to keep all lot coding consistent across the shop floor:

- Pull the material cert slip taped to the end of the leftover bar stock from this run, and copy the first 6 digits of the material lot number printed in the top right corner of the slip.
- Add a hyphen, then the 2-character machine ID for the CNC lathe you used for this cut, posted on the front control panel above the emergency stop.
- Add a second hyphen, then the 1-digit shift code (1 for first, 2 for second, 3 for third) matching your current scheduled shift.
- Add a third hyphen, then the 2-digit numerical date of the run, using the date posted on the wall clock above the parts washing station.
Illustrative example: If the material lot number is 789456-011, you ran the parts on machine L2, you’re on second shift, and the date is the 14th, your full lot code is 789456-L2-2-14. You double-check each digit as you write, because transposed numbers here trigger a full traceability audit that ties up the quality team for half a day, even if no parts are defective. You use a black fine-tip permanent marker for the line, so the code does not smudge if the traveler gets splashed with cutting fluid or washing solution later. You avoid writing over any pre-printed lines or existing notes on the traveler, so all prior operation data stays fully legible for downstream teams.
This First Piece Lot Verification Checklist
You set the first cut part from this run aside on your bench before you stacked the rest of the parts in the wire bin, specifically for this verification step. You etch the full lot code you just wrote into the flat, un-machined face of that first piece using the electric engraver mounted above your tool chest, making sure the characters are deep enough to stay visible through all subsequent surface treatments, including bead blasting and anodizing. You run your finger over the etched characters to confirm they are legible, and cross-check each digit against the code on the traveler to catch any typos before you move forward. You only need to mark the first piece for now, not every part in the run, because this piece stays clipped to the front of the traveler until all operations are complete, acting as a physical reference for every operator who works on the batch. You add a small tick mark next to the lot code line on the traveler to confirm you completed the marking and verification step, so the next operator knows the code is validated. You can grab a replacement engraver tip from the supply bin at the Traveler Desk if the current one drags or leaves faint marks that are hard to read later. If the un-machined face of the first piece is too small to fit the full lot code, you etch the first 8 characters and add a small dot on the edge of the part to indicate a truncated code, with a note next to the lot line on the traveler explaining the truncation.
This Cert’s Cross-Reference Requirement
Once the lot code is written and the first piece is marked, you pull the full material cert slip from the end of the leftover bar stock and tape it securely to the back of the traveler, making sure no edges stick out that can catch on other travelers in the queue and tear. The cert includes material composition data, mill heat treat results, and dimensional test data for the specific bar stock you used for this run, which the quality team cross-references against the lot code during final inspection to confirm the parts meet order specifications. You do not need to copy any additional data from the cert onto the traveler, but you do need to confirm that the lot number on the cert matches the number printed on the metal tag that was zip-tied to the bar stock when you pulled it from the raw materials rack at the start of your shift. If the cert is missing or the lot numbers do not match, you flag the issue to your shift lead before you move the parts to the next station, so the team can source the correct cert before the run proceeds. If you have 12 inches or more of bar stock left after this run, you write the same lot code on the cut end of the leftover piece with a white paint marker, so the next operator who uses that stock knows exactly which cert to pull for their own run, eliminating redundant cross-checks. You avoid folding the cert when you tape it to the traveler, so all small print test results stay fully visible for the quality team’s review.
When you open this traveler for the finishing operation
This is the next time you handle this sheet, when you pull it from the production queue 48 hours from now to prep the batch for glass bead blasting and type III anodizing. The first thing you do when you pick up the traveler is cross-check the lot code etched on the clipped first piece against the code written on the lot line, to confirm no one swapped the traveler or the first piece between runs, a common mix-up when batches of similar parts are queued next to each other. You then count the number of parts in the wire bin against the 42-unit quantity listed on the traveler, to account for any parts that were scrapped during the intermediate tapping operation that runs after your current deburring step. You note any scrap count directly below the lot code line, with your initials next to the number, so the quality team knows exactly how many parts entered the finishing step, no guesswork required. You only pull the cert from the back of the traveler at this step if the part count is off by more than two units, to cross-check the lot code against the run log and make sure no parts were accidentally pulled for a different order. If any parts fail dimensional check during your finishing prep, you write the full lot code on the scrap tag tied to each failed part, so the scrap processing team can log which run the defective parts came from without having to track down the traveler later. You do not modify the original lot code at this step, even if you add scrap counts or other notes, because the original code stays tied to the run for its full lifecycle, from raw stock to final delivery. You also confirm the tick mark next to the lot line is present before you start the finishing process, to ensure no prior operator skipped the initial verification step before moving the batch through production.
