Outside Processing Noted on the Traveler

A step says the parts leave the building. They are still in your pan. You run a finger along the annotated edge of the sheet where the lead tech scrawled a neon pink highlight around the outside processing line, double-checking you didn’t misread the operation number. No one left a pre-filled packing slip tucked in the back of the binder, so you know you’re the first person to hit this step for the batch. You count the 12 4140 steel sleeves in your pan once more to confirm the count matches the quantity listed at the top of the sheet.

Outside processing vendor requirements for this 4140 sleeve batch

You only send this specific batch to the PTFE coating vendor on Westside Drive, not the anodizing vendor you use for aluminum parts, because the low-friction coating specified for these sleeves requires a 200-degree pre-bake step that only the Westside facility is set up to run for carbon steel parts. You cross-reference the vendor’s posted turnaround time on the pinned bulletin by the front door, and note that you can expect the parts back in 3 business days, no rush fees apply for this order. Illustrative example: If you drop the parts off before 10 a.m. on a Tuesday, the vendor logs receipt by 11 a.m. and completes the coating run by end of day Thursday, with parts ready for pickup by 9 a.m. Friday. You confirm the vendor’s current address and contact number are printed on the lower left corner of the traveler, so you don’t have to look up the info mid-trip.

Outside Processing Noted on the Traveler
The part sits on a cloth.

Required traveler annotations for this 4140 sleeve batch to complete before parts leave your bench

All annotations must be made in permanent black ballpoint pen to avoid smudging from shop grease, moisture, or rough handling during transport. You fill out each required entry before you seal the part box, and cross-check each entry twice to avoid errors that could delay processing at the vendor facility.

Annotation Where to enter it Verification check
Exact part count being sent Line 14, right-hand margin Match the count to the number of parts in your pan before you seal the shipping container
Date and time of drop-off Line 14, left-hand margin Cross-check with the time stamp you get on the vendor’s drop-off receipt
Your employee ID number Line 15, signature block Confirm the ID matches the number printed on your badge to avoid processing delays for the batch
Vendor contact name who accepts the parts Line 15, notes field Write their full first and last name, no nicknames, to make follow-up easy if needed

If you need to correct an error, draw a single thin line through the incorrect text, write the correct information directly next to it, and add your initials next to the change to confirm the edit is intentional.

Pre-shipping processing check for 4140 sleeve surface burrs and dimensional consistency

Before you pack the parts, you run a fine-grit deburr wheel along the inner and outer edges of each sleeve to remove any leftover micro-burrs from the lathe operation you completed earlier today. Burrs left on the part surface will prevent the PTFE coating from adhering evenly, leading to uneven wear once the sleeves are installed in the final assembly. You spot-check 3 random sleeves with a digital micrometer to confirm the outer diameter is within the ±0.002 inch tolerance listed on line 7 of the traveler, to make sure you didn’t have a tool drift issue during the lathe run that would be hidden by the coating. You wipe each sleeve down with a lint-free cloth and isopropyl alcohol to remove all cutting fluid residue, then place them in a sealed plastic bag with a desiccant packet to avoid rust forming during transport to the vendor. You seal the bag with tamper-evident tape, so you can confirm no parts were removed or adjusted during transit when the batch returns.

Drop-off traveler confirmation steps for this batch’s third-party coating facility

You tuck the traveler in a clear waterproof sleeve taped to the outside of the part box, so the vendor can pull it out and review the requirements without opening the box and exposing the parts to dust or moisture. When you arrive at the vendor’s receiving desk, you point out the highlighted coating thickness requirement on line 13 of the traveler to the receiving associate, to make sure they flag the batch for the correct coating run, not the thicker industrial coating they use for heavy equipment parts. You get a physical drop-off receipt from the associate, staple it to the back of the traveler before you leave the facility, and note the receipt number in the notes field on line 15 as soon as you get back to your bench. If you have questions about any vendor requirements before you leave the shop, you can stop by the Traveler Desk to ask the lead scheduler for clarification before you load the parts into your truck. You don’t leave the facility until you confirm the associate logs the batch into their system with the correct job number listed at the top of the traveler, to avoid the batch getting mixed in with other unrelated orders.

Returned processing quality checks for this 4140 sleeve batch before you sign off on the coating operation

When the parts come back to the shop, you first cross-reference the count on the vendor’s delivery receipt to the count you wrote on line 14 of the traveler, to make sure no sleeves were lost during processing. You run a visual check of each sleeve’s coating to look for bare spots, bubbling, or uneven coverage, and use a coating thickness gauge to spot check 5 random parts to confirm the coating falls within the 0.001 to 0.003 inch thickness requirement listed on the traveler. You set aside any parts that fail the visual or thickness check in a separate red bin, and note the number of failed parts on line 16 of the traveler, so the lead tech can review them and decide if they need to be re-coated or scrapped. You don’t sign off on the operation block for the coating step until all parts pass your initial checks, to avoid moving faulty parts to the next machining operation. You log the date and time of return on line 16, and add your initials next to the count entry to confirm you verified the full batch is accounted for.

Post-receipt traveler review steps for this 4140 sleeve batch when you pull it back for final machining

When you pick this traveler back up to start the final boring operation for the sleeve inner diameters, you first review all annotations added during the outside processing step to confirm the batch went to the correct vendor, was received back within the expected turnaround window, and passed all initial quality checks. You cross-reference the coating thickness notes you added earlier to make sure you adjust your boring tool offset to account for the coating thickness, so the final inner diameter falls within the specified tolerance. You confirm the part count matches the number listed on line 16 before you set up the first part in your CNC mill, to avoid wasting time running parts that were already marked for scrap. You initial the top of line 17 to confirm you reviewed all processing notes before you start the final operation, so the next tech who picks up the batch knows you verified all prior steps are complete. You set the traveler in the front slot of your pan as you load the first part, so you can reference it quickly if you notice any unexpected dimensional variation during the first run.

About · Contact · Privacy · Disclaimer · Advertising · Terms