Test Report Number vs the Heat Number

Two numbers are on the cert. Only one of them is the heat. You lean over the print spread next to the raw stock bar, squinting at the fine print below the mill logo. You pull the digital copy of the form up on the tablet mounted at your Traveler Desk to cross-reference before you make a mark on the physical copy. You fumble for your caliper case, then pause because mixing these numbers up means the entire run gets scrapped before you even make the first cut.

Production Traveler Test Report Number Entry vs Production Traveler Heat Number Entry

These two fields sit side by side on the top left of the first page of the document, formatted with identical input boxes and nearly identical label text, making them easy to mix up if you rush through pre-run setup. The test report number is the unique identifier for the specific batch of mechanical and chemical tests the mill ran on the batch of metal you are using for this job, while the heat number is the unique identifier for the entire molten pour of metal that your raw stock was extruded or cut from. Many mills print the test report number in a smaller font directly below the heat number on the front of the cert, so slow down to make sure you pull the correct code for each field. Illustrative example: a recent batch of 4140 steel bars was pulled from the production queue at pre-production check because a machinist entered heat number 6281-M into the test report number field, when the correct test report number for that heat was TR-76281. This mix-up added three hours of rework time to the job, as the team had to re-log all stock and re-submit the pre-production paperwork for approval. You can avoid this delay by highlighting the heat number on the cert with orange highlighter and the test report number with yellow before you start filling out any fields, so you have a clear visual reference for each code.

Test Report Number vs the Heat Number
The packet stays closed on the bench.

Raw Stock Log Test Report Number Field vs Raw Stock Log Heat Number Field

This portion of the document appears on the third page, directly below the section where you note the length and diameter of the raw stock bar you are cutting for this run. The heat number field here exists to tie the specific bar you are using to the original mill pour, while the test report number field exists to tie that same bar to the specific test results that confirm the material meets the job’s required strength and chemical composition requirements. You follow this 4-step process to fill out these fields correctly every time:

  1. Wipe any cutting fluid, surface rust, or shipping grime off the stamped end of the raw stock bar to reveal the full stenciled heat number, making sure no alphanumeric characters are obscured by residue.
  2. Locate the matching heat number on the front of the mill cert, then highlight the corresponding test report number printed directly below it with your yellow highlighter to set it apart from surrounding text.
  3. Write the full heat number in the designated field on the raw stock log first, then copy the highlighted test report number into the adjacent field, double-checking each character as you go to avoid transposing numbers or mixing up letters like O and 0.
  4. Initial next to both fields to confirm you completed the cross-check before you make the first cut on the raw stock, so you have a record of who verified the material match if questions come up later in the run.

If you swap these numbers in this section, you end up logging stock that does not match the approved material for the job, which can lead to parts failing stress or hardness tests during final inspection, even if all your dimensional cuts are perfect.

First Article Inspection Test Report Number Field vs First Article Inspection Heat Number Field

This portion of the document sits on the fourth page, directly next to the dimensional check fields for the first part you machine from the raw stock bar. The heat number field here is for recording the code you etch onto the non-mating surface of the first part for permanent traceability, while the test report number field is for documenting the matching test results that will be attached to the first article packet sent to the quality team for review. You do not etch the test report number onto the part, but you do need to make sure the number you enter in this field matches the one you logged earlier in the raw stock section, so the quality team can pull the correct material property data if they run any additional tests on the first article, like hardness checks or chemical composition spot tests. If you mix these numbers up here, the first article will get sent back to you for correction, which adds at least two hours to your total run time, as you have to re-submit the paperwork and wait for a second round of approval before you can continue machining the rest of the run. You use the carbide scribe you keep in your apron pocket to etch the heat number onto a flat, non-functional surface of the part, so it remains visible even after powder coating or finishing processes are applied later in the production process. If you are working with small parts that do not have room for a full etched number, you can note the location of the heat number label on the bulk packaging of the parts in the adjacent notes field for reference.

Post-Run Audit Test Report Number Validation vs Post-Run Audit Heat Number Validation

This is the section you return to three days after you complete the full run of parts, when the quality team pulls the same document you filled out during production for final audit before parts are cleared for shipment. You open the same sheet to confirm that all test report number and heat number entries match across every section of the document, from the top of the first page to the raw stock log to the first article inspection section. You also cross-reference both numbers with the mill cert attached to the back of the document to make sure there are no typos or transposed characters that could cause traceability issues if a part ever fails in the field. You will also cross-check the heat number you logged against the etched numbers on 10% of the finished parts pulled at random from the run, to make sure you did not accidentally switch to a different bar of material halfway through the run without logging the change. If you find a small mismatch during this audit, you can correct it with a dated initial next to the fix, before the parts leave the facility, which saves you from having to coordinate a full recall of the run if a mismatch is discovered later by the client. You do not need to fill out any new fields during this step, just sign off on the validation section to confirm all entries are consistent and accurate, and add any relevant notes if you had to pull stock from a second heat halfway through the run to complete the full order. You also attach any supplementary test results for additional heats of material used during the run to the back of the document, so all traceability data lives in one place for future reference.

About · Contact · Privacy · Disclaimer · Advertising · Terms